PWS Car Dent Repair Tools Puller Removal Kit Slide Hammer Reverse Hammer Tool Body Suction Cup Adhesive Blue Glue Tabs

Features:
1. Slide hammer is more powerful for dent repair, conquer big dent.
2. The principle is making glue tabs stick on the dent and use tools pulling the tabs and lift the dent.
3. Big dent needs slide hammer or PWS puller; small dent needs mini dent lifter or pulling bridge.
4. Different tabs for different dent lifter or the Slide hammer, works with all glue pullers.
5. Use a slide hammer or dent lifter or any pulling tools lift the dent, try many times.

How to use:
1.Clean the dent with a clean wet cloth;
2.Mount the glue stick into the glue gun, pull the trigger to let the glue stick enter into the glue gun, connect the power source and preheat for 5 minutes;
3.Use a proper drawing gasket. Large dent requires a large drawing gasket.
4. Pull the trigger and apply the drawing gasket with extruded glue;
5. Fast place the drawing gasket with hot melt glue at the center of dent, press lightly until the glue cures and adheres;
6. Align the PWS T-shaped repairer and press the drawing gasket with hot melt glue, pull the sliding rod backwards to pull up the dent;
7. Check with a Line board. If dent still exists, knock it slightly with a flattening hammer or pen;
8. Clean the repaired place with a clean wet cloth.

Question 1: The glue is not strong, the glue is debonded, what is the reason?

1. The viscosity of hot melt adhesive is related to the temperature. The ideal temperature is 20°C-28°C.

Note: Do not operate under the sun in summer, and the operating temperature in winter is above 10 ℃ (if the weather is very cold, you can first pour hot water on the wagon in the recess)

2. If the car has been waxed or plated with crystal film or the material of the recess is not iron sheet, the stickiness of the tape will be greatly affected.

3. It may be that the product is dusty during use. Before use, it is best to use alcohol to clean the rubber strip, the dent surface and the gasket.

4. If it is degummed during operation at ideal temperature, this is a normal phenomenon, and it only needs to repeat the operation.

If the depression cannot be repaired after repeated operations, it may be that the puller is not suitable for processing the depression. This is related to the shape, position and size of the depression. Not all depressions can be repaired with one product, which has nothing to do with the glue.

Question 2: How to remove the glue ？

You can use alcohol above 95 degrees, while tearing it again and spraying alcohol, the residual glue can be buttoned off with your fingernails. Asphalt, gasoline or diesel can also be used.

(Because alcohol is flammable and cannot be transported, please buy it locally. Sorry for the inconvenience caused.)

Note:

1. It is not recommended to use if the body has been waxed, there is a car coat, a film has been coated, or the paint surface is cracked.

2. The dent is not a metal sheet, or the dent is in a particularly hard place such as the body beam and cannot be repaired with tools.

If there is any problem in the repair process, please contact us, we will provide professional guidance online.

Note: The alcohol bottle in this set is an empty bottle of non-alcoholic liquid de-gluing water

[Set 3-37Pcs]:
23x Short Blue Tabs(23 Sizes)
4 * Long Blue Tabs (2 Sizes)
2 * holder   (2 Sizes)
1x T-Bar Tools
1x 20W Glue Gun(EU Plug)
3x Yellow Glue Sticks

1x Yellow Shovel

1x Blue Towel

1x Alcohol Bottle (Alcohol not included)

[Set 3-37Pcs(US Plug)]:
23x Short Blue Tabs(23 Sizes)
4 * Long Blue Tabs (2 Sizes)
2 * holder   (2 Sizes)
1x T-Bar Tools
1x 20W Glue Gun(US Plug)
3x Yellow Glue Sticks

Description:
This PWS Paintless Dent Repair T-Bar puller is a lightweight glue tab pulling tool, meant to be used when repairing pressure dents and any dent that isn’t sharp or creased.
The tension puller works well with a tap down hammer when pulling large dents.
It’s very easy to control, everyone can removal the dent easily by yourself.